I don't wanna go through the whole process of getting parts i don't kneed till it starts working.
Filed under: Clothes Dryer Parts
Like this post? Subscribe to my RSS feed and get loads more!
My Dryer Stopped Heating Up, Will Spin the Clothes but No Heat. What's the First Part I Should Check?
10 Comments
Leave a Reply
Repair Clinic Live Chat Resource
Click The Live Chat Button At The Top Of The Next Page
ebay Deals
 137029500 DRYER ELECTRICAL HARNESS KENMORE FRIGIDAIRE ELECTROLUX NEW PART NTO fz $9.00 Time Remaining: 39m |
 W10007310 DRYER DRIVE MOTOR KENMORE WHIRLPOOL NEW PART NTO uz $118.00 Time Remaining: 1h 9m |
 WE4M513 DRYER USER INTERFACE BOARD ASSEMBLY GE NEW PART NTO pz $54.00 Time Remaining: 1h 27m |
 280148 DRYER THERMAL CUTOFF KENMORE WHIRLPOOL MAYTAG NEW PART NTO fz $20.00 Time Remaining: 1h 58m |
 8558178 DRYER ELECTRONIC CONTROL KENMORE WHIRLPOOL KITCHENAID NEW PART NTO fz $106.00 Time Remaining: 2h 23m |
 W10185987 DRYER TIMER WHIRLPOOL NEW PART NTO pz $70.00 Time Remaining: 2h 27m |
Welcome Danny Boy ( Good Name )
heating element: and from your question it doesn’t sound like you’ll have a problem getting to it. I’d remove it and inspect it, what you’ll most likely see is the coiled heating wire has a break in it. If so you know how to order parts but I’d also replace the little thermostat, I think some folks have referred to it as a fuse?? ? Anyway its wired inline with the heating coil. These get hot as well and they do work together their cheap. Inspect the wire ends as well; I’ve seen them burned and nasty. If all the above holds true check you vent before ya push the dryer back for a build-up of lint. Especially if it vents up into the attic, over time they get filled or restricted and add to the heat build up of the heating coil and causes them to go out prematurely.
i would check the heater see if its on
then the hose
now here is place and find your model number and see if this can help
http://www.pcappliancerepair.com/
the heating element..depending on the dryer you can check it by opening the door,holding down the little arm switch and having someone turn the dryer on..it should start glowing inside a light orange color.
it would be the element, you can find a manual for almost everything on "diplodocs.com"
if you have a high efficiency dryer, where it senses the dryness of the clothes, you may have an issue with the sensor. A dryer sheet covered up my sensor, and the heat never turned on because the dryer thought everything was dry! CRAZY!
The very first thing you check is power. Make sure you have full 220V to the dryer. You could have a dead leg (no voltage on one leg of the 220V). Pumps will work, motors will work, timing mechanisms will work, but heating elements won’t if you don’t have 220V. So, that’s the first thing you check for.
First off, this would be allot easier if you had stated the make and model, and if it was electric or gas.
Different brands have different ways of doing things, and gas vs electric, well, that’s kind of self explanatory.
If its a gas dryer, the easiest thing to check, and the most probable, would be the ignitor or glow bar, make sure that’s glowing red. If that gets cracked, your burner will never come on. It could also be a bad gas valve, operational thermostat, or high limit thermostat/thermal fuse.
If its electric, it could be bad heating elements, bad operational thermostat or bad high limit thermostat/thermal fuse.
Obstructed airflow, be it a plugged lint filter or plugged dryer hose, even a dryer hose that’s fallen off, will greatly extend the drying time, but the clothes will still get warm.
OK, first of all check the vent, If the vent is crushed or blocked up the dryers t’stat will turn off the element and not dry the clothes. Check where it vents out side the home buy turning it on and go out and see if the flap opens. If you can reach it feel for the rate of flow and the temp. Should be a good flow and the temp should feel pretty warm. If thats ok, move on to make sure the dryer has proper voltage. Make sure the breaker is not partially tripped. If you have 220 to the outlet, unplug it and check the power cord connections at the dryer. If these are even loose a smidge they could cause problems including fire. Make sure they are all tight. If all of these things are ok then you need a part and I need a model number. I will tell you other checks and what part you may need. Good luck.
There are heat sensors that prevent the dryer from overheating, I would check them first as they seem to go out more often than a heating element. Check the wiring to be sure it is not burnt or damaged. Also check the voltage to be sure you are getting 220v. I am assuming this is an electric dryer.
http://www.repairclinic.com